Aside

Camping!

Why do we build these things? To go camping! Even though we’re not done with the Toaster, it’s still camping season, so of course we’re going to get out a bit here and there. What you bring with you changes a bit from tent camping (car camping at festivals to be specific). Roy and I had our gear, both the packing and unpacking of it, down to an art. Two trunks, first one was packed with (in order from top on down to the bottom): a tarp, its stakes, our tent, its stakes, air mattress, battery powered pump, batteries for the pump in a baggie. Second one was sleeping bags, giant horse blanket, first aid kit, toiletry kit and lights. We brought our clothes/costumes in bins that fit inside a trunk, the other served as a bench or low table. Food came in coolers, and we did the best we could. Teardown was: box up laundry, pack the lights, sleeping bags, blanket, toiletry kit and 1st aid kit in one trunk. Second trunk: deflate air mattress with pump, take out and bag batteries, pack batteries and pump on the bottom, fold mattress, pack on bottom, take down tent, pack tent and tent stakes, clean tarp, pack tarp stakes and tarp.

When I first decided to build Shorty, it was because we had to pack up one too many times in the rain, or after the rain, or someplace extraordinarily soggy. I was done flicking slugs off the bottom of the tarp, of checking for spiders before packing the trunk, of having to unpack the tent to dry it before tucking it completely away. Traveling with a trailer is a pretty great thing, both for extended roadtrips and for festivals, but the way we use it is a little different depending on the context. Last summer, we went on a 3 week tour of the Western interior, hitting up places like Yellowstone, Grand Teton, Glacier, and several smaller parks in between. This summer, it seems we’ve been hitting festival after festival, and the differences between the two contexts are worth mentioning.

For roadtripping, we like to be able to pull over and have a picnic out of the back and be able to pull over and crawl into bed, no matter where we are. All clothes and toiletries must fit in the cabinets, although we do keep a laundry bag stashed in the footwell. Doing laundry on the road helps keep the volume of clothes you need to bring down, and provides a nice pause in places you normally wouldn’t stop. We make the bed every morning once we’re out, because someone will stop us at some point during the day and want to look inside, and it makes it easier to climb in at the end of the day without needing to untangle the sheets. We keep two floor mats to put outside each door. They provide a good place to kick your shoes off. We also bring our camp chairs to put our feet up and watch the sky at the end of the day. The galley is also pretty spartan. Cooler and stove live back there, along with the storage drawers and bins for dishes. Dry goods live in a picnic basket that travels in the car (because driving munchies), and a small cooler for drinks also lives in the car (because driving caffeine). We took to keeping a small container with cold cuts, cheese, mustard, and pickles in the drink cooler, which made it easier to grab that and the basket and picnic wherever the mood struck us. Larger food lived in the large cooler. Mornings were usually tea, yogurt, and granola. Lunchtime, sandwiches and chips. Dinner, some larger thing we’d keep frozen in the large cooler. (hm, maybe we should do a recipes post soon.) Everything gets washed and put away asap. A couple of games, a couple of solar lights, not much is needed when you’re in a different place almost every night.

Wanna stop here for lunch?

At a festival (or a rally), you’re in one spot for anywhere from 2 to 7 or more days. The essentials expand to include a shade tent, a camp rug, a large folding table, a more involved lighting setup (usually to mark your stakes and lines to prevent injury and to serve as a beacon some inevitable late night), dutch ovens and the associated tools (charcoal, tongs, fire trays, mitts…yeah, a post on feeding yourself should happen). Even though teardrops are awesome for camping convenience, if we’re going someplace for the long haul, we still wind up with gear taking up space on the bed which means taking the time to get set up once we land. However, the time and labor for setup is much lower than when we were tenting, and the ability to change the setup after the fact is much easier. “Oh, the sun comes up over there? Let’s roll it into position, then!”

We are still working on the Toaster, there will be updates at some point, but we do still have a few more roadtrips and campouts planned for what’s left of summer.

Image

Paper Dolls

When I was little, I would entertain myself making paper dolls. I’d make them out of anything I could get my hands on, comic books, newspaper ads, magazines, I would cut out things that caught my eye. I had a file full of women, men, animals, tools, dishes, and sheets straight out of catalogs of fully or partially decorated rooms. Rainy afternoons or winter evenings, I would set up a TV tray, pick a setting from my room collection, and start to assemble a scene to play with. Turns out, I still play with paper dolls.

When you want to make a full scale model of something, you need a cheap and easy material to work with that can handle some abuse. Thanks to the lovely people at SCRAP, I found just the thing. SCRAP winds up getting all the signage from conferences at Moscone (and probably other places I’m not aware of). That means they are usually swimming in sheets upon sheets of foamcore. Not just any foamcore, either. The stuff they have is 1/2 inch thick, and surfaced with a thin plastic. This stuff is meant for holding up to being stumbled into and knocked down. Perfect for cutting and pinning together with 8 penny nails. We taped together some larger sheets and cut out the side profile, then cut the pieces for the shelves, counters, and cabinets. Today, we pieced them together. The plastic coating has a satisfying snap and the 8 penny nails make a nice squeaking sound as you punch through. All the horizontals are placed, so the next step is to grab the mattress out of the current trailer, throw it in the mockup, and see how it feels spacewise. At this point, we can decide on things like “Do we want to modify the headboard or scrap it completely?” “Should we lower the cabinets?” “Will a shoe and blanket shelf fit in the footwell?” Since it’s just foamcore and nails, we can pull the nails and move things where we want, and compare how the different placements feel.

DSC_0857

For now, however, we found the balance point, and suspended it from a hanging bike rack in our loft. This way, we’re not walking into and/or around it all the time, but we can still pull it down to work with it. We still want to do things like determine cooler tray placement, stove rack, dish storage, food and water storage, and the like. (yay, using paper dolls to figure out fiddly details ahead of time!)

DSC_0860

Next up are a few camping trips. I’ll go into prep for those here a little later on to share and enjoy!

Image

Watching Paint Dry

What do you do after priming a trailer frame? You paint it! Then, you watch it dry, flip it over and paint it again. Once that dries, you flip it and paint it some more. Paint, dry, flip, paint, dry, flip, noticing a pattern here? We’re using ultra high gloss paint, so even after it dries, it’s got quite a bit of shine to it. Ideally, I’d like for it to have a nice Bakelite look to it, we’ll see how the final version turns out.
IMG_20140602_165019

Image

Optimus Prime

Bad pun, I know. Blame Roy.
IMG_20140524_133833
This weekend, we smoothed out the few remaining burrs on the frame, brushed it,  knocked the rust off and cleaned it, then gave it a coat of primer.
1400969964242
Flipped it on it’s back, primed the bottom and sides, let it dry. Came back the next day, flipped it right side up, primed the top and touched up the sides.
IMG_20140525
It was sweaty, stinky, and somewhat tough because it was so nice outside, but it’s done now. Left a wet paint sign on the front and called it a day.

American Steel

At some point, we were asked “Wait, don’t you guys live in San Francisco?” Yes, yes we do. “Where do you find space to up and build a trailer in San Francisco?” The answer, my friends, is Oakland.

american-steel

The Studios

Roy and I went in with some friends on a space at American Steel Studios in Oakland, and so far, we’ve been really happy with it. It’s the old American Steel complex on Mandela Blvd, which used to be the Cypress Structure before the Loma Prieta earthquake. After they tore down the structure, it became Mandela Blvd, with a park and path through the middle. It’s a great space to work in, with really interesting neighbors in the complex. You can find fine artists, industrial artists, commercial vendors, and just about everything in between. The complex is packed full of people that make things. I’m still not quite sure where we fall on the spectrum, whether we’re industrial artists, or closer to the neighborhood of craft work. Doesn’t really matter right now. I’m just happy we found a studio to call home.

DSC_0850

Where the toast happens.

Aside

Why Toaster?

I love toast. I mean really love toast.
When I was little, I would wake up in the morning, go to the kitchen, and make myself toast. Preferably with lots of butter, jelly, and cheese, or the occasional smear of Braunschweiger. (Don’t judge me!) The toaster would greet me every morning, gleaming and faithful. It was the toaster my parents got for their wedding in 1962. It was a Toastmaster.

the original

the original

When I started making noises about building a second trailer, Roy and I agreed that we needed some sort of design or theme to build around. The first trailer was done because I wanted to build a trailer, period, and design and planning didn’t really enter the equation until after the fact, when we looked at it and thought “Wow, that’s kinda generic.” Riffing one night, we landed on the topic of the toaster, my childhood toaster, and all the good feelings I associated with it. The closest profile we could figure to match the profile was a Benroy, so that’s what we used as a starting point for our plans. It looks rather toastery. And voila! A theme was born!

Image

Framed!

This weekend, we paid a visit to our friends Debbie and Randy of Desert Metal Products in Lovelock, NV to weld the frame. (And hang out. And play Qwirkle!)

20140516_160601

It was a full, but super productive day! We couldn’t tow the trailer back home with us, no VIN#, no plates, and since we were driving so far, we opted to rent a cargo trailer, load the frame onto it, and drag it back home. It worked great, and we were able to unload the frame at American Steel yesterday!

Next up: Shop day to clean and stage the shop, then to clean and paint the frame! (Should also figure out how to make a public calendar to share dates!)

Post From the Wiki Last Week

20140503 Courtney

Started the build journal page. Need someplace to talk about this in the abstract, right?

Yesterday, we received our largest delivery of supplies yet: coupler, stabilizer jacks, swivel jack, rims, tires, valve stems, fenders, axle-less suspension system. Today, we got the tail/turn lights. We already had the safety chains and connectors. We’re scheduled to go weld the frame together on the 16th. I’ve started snapping pictures of things as they come in, mostly out of excitement, but I’m just realizing we should set up someplace to put photos, because there will be a TON more relatively soon, and we’ll want to share.

20140502_102720

Also starting to think about scheduling. We’re doing the frame in Lovelock (road trip!! woo!!), but once we get it back to AmSteel, we’ll need to start some sort of scheduling 1) so we know what we’re doing next and 2) so we can share with other people what we’re doing next. I’ll probably take down this gawd awful pink dry erase board from above my desk and mount it in the shop. That’ll be a good place to leave notes and think on the fly down there. And now I’m thinking about how to share info with folks in a general sense.